Sprzedam tokarkę do metalu Doosan PUMA 400LB poprzez aukcję

FANUC F21iTB control,
swing over bed - 770 mm,
turning diameter (recommended) - 380 mm,
maximum turning diameter - 550 mm,
maximum turning length - 2,093 mm,
work in the chuck - 700 kg,
work with a bar (tailstock) - 1,700 kg,
bar diameter in the spindle - 116.5 mm,
spindle holder - 380 mm,
spindle - A2#11 ASA,
spindle diameter (front/rear) - (180/170) mm,
spindle bore 132 mm,
spindle taper clearance - Φ 117.5 mm,
Cylinder clearance - Φ 117.5 mm,
Spindle motor power (continuous/30 min) - Fanuc α 22 22/26 kW,
Spindle speed range - 2,000 rpm,
Maximum spindle torque - 1,761 N.m,
X axis feed - 362 (87 + 275) mm
Z axis feed - 2,155 mm
X axis rapid traverse - 16 m/min
Z axis rapid traverse - 18 m/min
X axis servo motor - Fanuc α 22 / 3,000iB 4.0 kW
Z axis servo motor - Fanuc α 40 / 3,000i 7.0 kW
Bed and saddle:
Tilt angle - 45 degrees,
Guide:
Bed (Z axis) ) - 420 mm,
X-axis saddle - 360 mm,
Tailstock - 300 mm,
Without DHI Base Holder and tools,
Storage capacity: 10 tools,
Turret position change: 1 position: 0.25 s,
Hydraulic tank capacity: 14 l,
Flow rate: (60 Hz / 50 Hz) (25 / 20.8) l/min,
Pressure: 2.2 kW x 4.0 MPa
Coolant tank capacity: 370 l,
Flow rate: 40 l/min,

Equipment:Programmable tailstock with movable quill,Automatic tool probe,14.5 bar coolant pump,Oil separator,Prepared for installation of the SLU4 hydraulic steady rest,SLU4 hydraulic steady rest,Chip conveyorl
transport dimenions:machine - 5342x179x2317mm,chip conveyor with cooling tank - 4900x1280x1700mm
FANUC F21iTB control, swing over bed - 770 mm, turning diameter (recommended) - 380 mm, maximum turning diameter - 550 mm, maximum turning length - 2,093 mm, work in the chuck - 700 kg, work with a bar (tailstock) - 1,700 kg, bar diameter in the spindle - 116.5 mm, spindle holder - 380 mm, spindle - A2#11 ASA, spindle diameter (front/rear) - (180/170) mm, spindle bore 132 mm, spindle taper clearance - Φ 117.5 mm, Cylinder clearance - Φ 117.5 mm, Spindle motor power (continuous/30 min) - Fanuc α 22 22/26 kW, Spindle speed range - 2,000 rpm, Maximum spindle torque - 1,761 N.m, X axis feed - 362 (87 + 275) mm Z axis feed - 2,155 mm X axis rapid traverse - 16 m/min Z axis rapid traverse - 18 m/min X axis servo motor - Fanuc α 22 / 3,000iB 4.0 kW Z axis servo motor - Fanuc α 40 / 3,000i 7.0 kW Bed and saddle: Tilt angle - 45 degrees, Guide: Bed (Z axis) ) - 420 mm, X-axis saddle - 360 mm, Tailstock - 300 mm, Without DHI Base Holder and tools, Storage capacity: 10 tools, Turret position change: 1 position: 0.25 s, Hydraulic tank capacity: 14 l, Flow rate: (60 Hz / 50 Hz) (25 / 20.8) l/min, Pressure: 2.2 kW x 4.0 MPa Coolant tank capacity: 370 l, Flow rate: 40 l/min, Equipment:Programmable tailstock with movable quill,Automatic tool probe,14.5 bar coolant pump,Oil separator,Prepared for installation of the SLU4 hydraulic steady rest,SLU4 hydraulic steady rest,Chip conveyorl
transport dimenions: machine - 5342x179x2317mm,chip conveyor with cooling tank - 4900x1280x1700mm
length: 6400
height: 2400
width: 2200

FANUC F21iTB Kontrolle,
Schaukel über das Bett – 770 mm,
Drehdurchmesser (empfohlen) - 380 mm,
Maximaler Drehdurchmesser - 550 mm,
maximale Drehlänge – 2.093 mm,
Arbeit im Chuck – 700 kg,
Arbeiten mit einer Stange (Heckstück) – 1.700 kg,
Stabdurchmesser in der Spindel – 116,5 mm,
Spindelhalter – 380 mm,
Spindel - A2#11 ASA,
Spindeldurchmesser (vorne/hinten) - (180/170) mm,
Spindelbohrung 132 mm,
Spindel-Kegelfreiheit – Φ 117,5 mm,
Zylinderfreiheit – Φ 117,5 mm,
Spindelmotorleistung (kontinuierlich/30 min) – Fanuc α 22 22/26 kW,
Spindeldrehzahlbereich – 2.000 U/min,
Maximales Spindeldrehmoment – 1.761 Nm,
X-Axen-Zuführung – 362 (87 + 275) mm
Z-Achsen-Zuführung – 2.155 mm
X-Achse Schnelldrehung – 16 m/min
Z-Achse Schnelldrehung – 18 m/min
X-Achsen-Servomotor – Fanuc α 22 / 3.000 iB 4,0 kW
Z-Achsen-Servomotor – Fanuc α 40 / 3.000i 7,0 kW
Bett und Sattel:
Neigungswinkel – 45 Grad,
Anleitung:
Bett (Z-Achse) – 420 mm,
X-Achsen-Sattel – 360 mm,
Heckstock – 300 mm,
Ohne DHI-Basishalter und Werkzeuge,
Lagerkapazität: 10 Werkzeuge,
Turmpositionsänderung: 1 Position: 0,25 s,
Hydrauliktankkapazität: 14 l,
Durchflussrate: (60 Hz / 50 Hz) (25 / 20,8) l/min,
Druck: 2,2 kW x 4,0 MPa
Kühlmitteltankkapazität: 370 l,
Durchflussrate: 40 l/min,

Ausrüstung: Programmierbarer Schlussstock mit beweglicher Feder, automatische Werkzeugprobe, 14,5-bar-Kühlmittelpumpe, Ölabscheider, vorbereitet für die Installation der SLU4-hydraulischen Stabilisator, SLU4-hydraulische Stationäre Halterung, Transportdimensionen des Spanförderbands
: Maschine - 5342x179x2317 mm, Späneförderband mit Kühltank - 4900x1280x1700 mm

Control FANUC F21iTB,
Oscilación sobre la cama - 770 mm,
diámetro de giro (recomendado) - 380 mm,
diámetro máximo de giro - 550 mm,
longitud máxima de giro - 2.093 mm,
trabajo en el mandril - 700 kg,
Trabajo con barra (contrapunto) - 1.700 kg,
diámetro de la barra en el husillo - 116,5 mm,
Soporte del husillo - 380 mm,
husillo - A2#11 ASA,
Diámetro del husillo (delantero/trasero) - (180/170) mm,
diámetro del husillo 132 mm,
Espacio para la conicidad del husillo - Φ 117,5 mm,
Espacio libre para los cilindros - Φ 117,5 mm,
Potencia del motor del husillo (continua/30 min) - Fanuc α 22 22/26 kW,
Rango de velocidades del husillo - 2.000 rpm,
Par máximo del eje - 1.761 N.m,
Alimentación del eje X - 362 (87 + 275) mm
Alimentación del eje Z - 2.155 mm
Giro rápido en el eje X - 16 m/min
Giro rápido en el eje Z - 18 m/min
Servomotor del eje X - Fanuc α 22 / 3.000iB 4,0 kW
Servomotor del eje Z - Fanuc α 40 / 3.000i 7,0 kW
Cama y silla:
Ángulo de inclinación - 45 grados,
guiar:
Cama (eje Z) - 420 mm,
Silla del eje X - 360 mm,
Contrapunto - 300 mm,
Sin el soporte base DHI ni las herramientas,
Capacidad de almacenamiento: 10 herramientas,
Cambio de posición de la torreta: 1 posición: 0,25 s,
Capacidad del depósito hidráulico: 14 l,
Caudal: (60 Hz / 50 Hz) (25 / 20,8) l/min,
Presión: 2,2 kW x 4,0 MPa
Capacidad del depósito de refrigerante: 370 l,
Caudal: 40 l/min,

Equipamiento: Contrapunto programable con quilla móvil, sonda automática para herramientas, bomba de refrigerante de 14,5 bar, separador de aceite, preparado para la instalación del soporte hidráulico estable SLU4, soporte estacionario hidráulico SLU4, transportador de astillas para transportadores de virutas
dimensiones: máquina - 5342x179x2317mm, transportador de astillas con tanque de refrigeración - 4900x1280x1700mm

Contrôle FANUC F21iTB,
Swing au-dessus du plateau - 770 mm,
diamètre de tournage (recommandé) - 380 mm,
diamètre maximal de rotation - 550 mm,
longueur maximale de rotation - 2 093 mm,
travail dans le mandrin - 700 kg,
travail avec une barre (crosse arrière) - 1 700 kg,
diamètre de la barre dans la broche - 116,5 mm,
Porte-broche - 380 mm,
broche - A2#11 ASA,
Diamètre de la broche (avant/arrière) - (180/170) mm,
Axe de fusée 132 mm,
Dégagement du conic de la broche - Φ 117,5 mm,
Jeu des cylindres - Φ 117,5 mm,
Puissance du moteur de broche (continue/30 min) - Fanuc α 22 22/26 kW,
Plage de vitesses de la broche - 2 000 tr/min,
Couple maximal de la broche - 1 761 N.m,
Alimentation de l’axe X - 362 (87 + 275) mm
Alimentation de l’axe Z - 2 155 mm
Rotation rapide sur l’axe X - 16 m/min
Rotation rapide sur l’axe Z - 18 m/min
Servomoteur à axe X - Fanuc α 22 / 3 000iB 4,0 kW
Moteur servomoteur à axe Z - Fanuc α 40 / 3 000i 7,0 kW
Lit et selle :
Angle d’inclinaison - 45 degrés,
guide:
Lit (axe Z) - 420 mm,
Selle axe X - 360 mm,
Contre-stock - 300 mm,
Sans support de base DHI ni outils,
Capacité de stockage : 10 outils,
Changement de position de la tourelle : 1 position : 0,25 s,
Capacité du réservoir hydraulique : 14 l,
Débit : (60 Hz / 50 Hz) (25 / 20,8) l/min,
Pression : 2,2 kW x 4,0 MPa
Capacité du réservoir de liquide de refroidissement : 370 l,
Débit : 40 l/min,

Équipement : Contre-papier programmable avec quille mobile, sonde automatique d’outil, pompe de refroidissement de 14,5 bars, séparateur d’huile, prêt pour l’installation du repos-papier hydraulique SLU4, repos-repos hydraulique SLU4, convoyeur de copeaux
Dimensions de transport : machine - 5342x179x2317mm, convoyeur à copeaux avec réservoir de refroidissement - 4900x1280x1700mm

Controllo FANUC F21iTB,
oscillazione sul letto - 770 mm,
Diametro di rotazione (consigliato) - 380 mm,
diametro massimo di rotazione - 550 mm,
lunghezza massima di rotazione - 2.093 mm,
lavoro nel mandrino - 700 kg,
lavorare con una barra (contropposizione) - 1.700 kg,
diametro della barra nel fuso - 116,5 mm,
Portamestini - 380 mm,
fuso - A2#11 ASA,
Diametro del mandrino (anteriore/posteriore) - (180/170) mm,
Alesaggio del perno 132 mm,
spazio per la conica del mandrino - Φ 117,5 mm,
Altezza dei cilindri - Φ 117,5 mm,
Potenza del motore del mandrino (continua/30 min) - Fanuc α 22 22/26 kW,
Intervallo di velocità del mandrino - 2.000 giri/min,
Coppia massima del mandrino - 1.761 N.m,
Alimentazione dell'asse X - 362 (87 + 275) mm
Alimentazione dell'asse Z - 2.155 mm
Traversata rapida sull'asse X - 16 m/min
Traversata rapida sull'asse Z - 18 m/min
Servomotore a asse X - Fanuc α 22 / 3.000iB 4,0 kW
Servomotore sull'asse Z - Fanuc α 40 / 3.000i 7,0 kW
Letto e sella:
Angolo di inclinazione - 45 gradi,
guida:
Piano (asse Z) - 420 mm,
Sella dell'asse X - 360 mm,
Contrapposizione - 300 mm,
Senza il portabase DHI e gli strumenti,
Capacità di stoccaggio: 10 attrezzi,
Cambio di posizione della torretta: 1 posizione: 0,25 s,
Capacità del serbatoio idraulico: 14 l,
Portata: (60 Hz / 50 Hz) (25 / 20,8) l/min,
Pressione: 2,2 kW x 4,0 MPa
Capacità del serbatoio del liquido refrigerante: 370 l,
Portata: 40 l/min,

Equipaggiamento: Controcalco programmabile con penna mobile, sonda automatica per utensili, pompa refrigerante da 14,5 bar, separatore dell'olio, preparato per l'installazione del supporto stabili idraulico SLU4, supporto stabili idraulico SLU4, nastro trasportatore
di trucioli Dimensioni di trasporto: macchina - 5342x179x2317mm, nastro trasportatore a trucioli con serbatoio di raffreddamento - 4900x1280x1700mm

FANUC F21iTB controle,
Schommel over bed - 770 mm,
Draaidiameter (aanbevolen) - 380 mm,
maximale draaidiameter - 550 mm,
Maximale draailengte - 2.093 mm,
Werk in de Chuck - 700 kg,
werken met een stang (staartstok) - 1.700 kg,
Staafdiameter in de spil - 116,5 mm,
Spilhouder - 380 mm,
spil - A2#11 ASA,
Spildiameter (voor/achter) - (180/170) mm,
Spoelboring 132 mm,
spil-taps speelruimte - Φ 117,5 mm,
Cilinderruimte - Φ 117,5 mm,
Spindelmotorvermogen (continu/30 min) - Fanuc α 22 22/26 kW,
Spilsnelheid - 2.000 tpm,
Maximaal spindelkoppel - 1.761 N.m,
X-as voeding - 362 (87 + 275) mm
Z-as voeding - 2.155 mm
X-as snelle dwarsgang - 16 m/min
Z-as snelle traverse - 18 m/min
X-as servomotor - Fanuc α 22 / 3.000iB 4,0 kW
Z-as servomotor - Fanuc α 40 / 3.000i 7,0 kW
Bed en zadel:
Hellingshoek - 45 graden,
leiden:
Bed (Z-as) - 420 mm,
X-as zadel - 360 mm,
Staartstuk - 300 mm,
Zonder DHI Base Holder en gereedschap,
Opslagcapaciteit: 10 gereedschappen,
Verandering van koepelpositie: 1 positie: 0,25 s,
Hydraulische tankcapaciteit: 14 l,
Debiet: (60 Hz / 50 Hz) (25 / 20,8) l/min,
Druk: 2,2 kW x 4,0 MPa
Koelvloeistoftankcapaciteit: 370 l,
Debietsnelheid: 40 l/min,

Uitrusting: Programmeerbare achterstuk met beweegbare ganzenveer, automatische gereedschapsprobe, 14,5 bar koelvloeistofpomp, olieafscheider, voorbereid voor installatie van de SLU4 hydraulische stabilisatie, SLU4 hydraulische stationaire rust, spaandertransportmiddelen
: machine - 5342x179x2317mm, spaantransportband met koeltank - 4900x1280x1700mm

Controlul FANUC F21iTB,
swing over bed - 770 mm,
Diametrul de viraj (recomandat) - 380 mm,
diametru maxim de rotație - 550 mm,
lungimea maximă de rotire - 2.093 mm,
Muncă în mandrină - 700 kg,
lucru cu bară (contrapat) - 1.700 kg,
diametrul barei în ax - 116,5 mm,
Suport pentru ax - 380 mm,
fus - A2#11 ASA,
Diametrul axului (față/spate) - (180/170) mm,
alențul axului 132 mm,
Spațiu pentru conicitatea axului - Φ 117,5 mm,
Spațiu liber al cilindrilor - Φ 117,5 mm,
Puterea motorului axului (continuă/30 min) - Fanuc α 22 22/26 kW,
Intervalul de viteză al axului - 2.000 rpm,
Cuplu maxim al axului - 1.761 N.m,
Alimentare pe axa X - 362 (87 + 275) mm
Alimentare pe axa Z - 2.155 mm
Traversare rapidă pe axa X - 16 m/min
Traversare rapidă pe axa Z - 18 m/min
Motor servo pe axa X - Fanuc α 22 / 3.000iB 4.0 kW
Motor servo pe axa Z - Fanuc α 40 / 3.000i 7,0 kW
Pat și șa:
Unghiul de înclinare - 45 de grade,
ghid:
Pat (axa Z) - 420 mm,
Șa axei X - 360 mm,
Contrajoc - 300 mm,
Fără suportul de bază DHI și unelte,
Capacitate de stocare: 10 unelte,
Schimbare poziție a turelei: 1 poziție: 0,25 s,
Capacitatea rezervorului hidraulic: 14 l,
Debit: (60 Hz / 50 Hz) (25 / 20,8) l/min,
Presiune: 2,2 kW x 4,0 MPa
Capacitatea rezervorului de lichid de răcire: 370 l,
Debit: 40 l/min,

Echipament: Contrapunct programabil cu pene mobilă, sondă automată pentru unelte, pompă de răcire de 14,5 bar, separator de ulei, pregătit pentru instalarea suportului hidraulic SLU4, suport hidraulic stabil SLU4, transportor de așchii
Dimensiuni de transport: Mașină - 5342x179x2317mm, transportor cu așchii cu rezervor de răcire - 4900x1280x1700mm